Onko kellään tietoa CANM8 CAN-väylä purkista ?
Tilasin sellaisen ja muuten asennus ok mutta ei anna pitkillä ohjausta ulostulosta
Vitosesssa LED valot ILS:llä
Vito W447 lisävalot
Re: Vito W447 lisävalot
Mistä ryöstit signaalit purkille? Itseänikin kiinnostaisi lisäpitkät ILS-Vitoon. Onko sinulla varmasti purkin asennus tehty valmistajan ohjeiden mukaisesti:
CANM8 CANNECT Installation, Mercedes V Class W447 2014 >
Vehicle CAN Bus Location
The CAN wires are located at the Ignition Barrel
CAN HI = BROWN / RED
CAN LO = BROWN
CANM8 CANNECT HIGHBEAM Wiring Instructions
HIGHBEAM Wire Wire Connection Point Or Output Function
WHITE > CAN HI Connection : Vehicle CAN HI wire
BLUE > CAN LO Connection : Vehicle CAN LO wire
RED > Connect via a 5 Amp fuse to a PERMANENT 12V supply.
BLACK > Connect to a good chassis ground point.
WHITE > CAN HI Connection : Vehicle CAN HI wire
PURPLE > Main Beam Output : 12v when Main Beam is on
Testing The Installation
Connect the interface to the plug-in wiring harness and turn the vehicles ignition 'on'.
The CANNECT interface switches on automatically when CAN activity is detected.
The interface has an LED status indicator next to the connection plug, which will illuminate
GREEN when valid CAN data has been identified by the interface. When the vheicle is moved, the
GREEN LED will flash to indicate that CAN Bus speed information is being processed.
If the LED indicator is illuminated RED for more than 10 seconds, the interface is functioning but
cannot identify the vehicle. It is very important that the interface is only connected to the vehicle
CAN Bus wiring at the connection point location detailed at the top of the page.
If the LED fails to illuminate or flash, there is a power connection problem - recheck the connections
If the LED flashes RED continuously, the interface is powered but is not reading CAN data. Check
the interface CAN HI and CAN LO connections are the correct way around. Also check that these
wires are connected to the CAN Bus wires as detailed above.
The CANNECT interface automatically switches off when the vehicle CAN Bus is inactive.
This can be tested by removing the keys from the ignition, closing all vehicle doors and
switching all auxilliary equipment 'off'. The interface LED should extinguish within 60 seconds.
CANM8 CANNECT Installation, Mercedes V Class W447 2014 >
Vehicle CAN Bus Location
The CAN wires are located at the Ignition Barrel
CAN HI = BROWN / RED
CAN LO = BROWN
CANM8 CANNECT HIGHBEAM Wiring Instructions
HIGHBEAM Wire Wire Connection Point Or Output Function
WHITE > CAN HI Connection : Vehicle CAN HI wire
BLUE > CAN LO Connection : Vehicle CAN LO wire
RED > Connect via a 5 Amp fuse to a PERMANENT 12V supply.
BLACK > Connect to a good chassis ground point.
WHITE > CAN HI Connection : Vehicle CAN HI wire
PURPLE > Main Beam Output : 12v when Main Beam is on
Testing The Installation
Connect the interface to the plug-in wiring harness and turn the vehicles ignition 'on'.
The CANNECT interface switches on automatically when CAN activity is detected.
The interface has an LED status indicator next to the connection plug, which will illuminate
GREEN when valid CAN data has been identified by the interface. When the vheicle is moved, the
GREEN LED will flash to indicate that CAN Bus speed information is being processed.
If the LED indicator is illuminated RED for more than 10 seconds, the interface is functioning but
cannot identify the vehicle. It is very important that the interface is only connected to the vehicle
CAN Bus wiring at the connection point location detailed at the top of the page.
If the LED fails to illuminate or flash, there is a power connection problem - recheck the connections
If the LED flashes RED continuously, the interface is powered but is not reading CAN data. Check
the interface CAN HI and CAN LO connections are the correct way around. Also check that these
wires are connected to the CAN Bus wires as detailed above.
The CANNECT interface automatically switches off when the vehicle CAN Bus is inactive.
This can be tested by removing the keys from the ignition, closing all vehicle doors and
switching all auxilliary equipment 'off'. The interface LED should extinguish within 60 seconds.
w447 119 Allradantrieb